Difference between revisions of "Fibre - Support Information"

From ExeWiki
Jump to: navigation, search
m (What type of equipment (MODEM, Filters…etc) will I need to set up the Optic Fibre service)
(I have more than two computers at home and need to share Internet simultaneously. Can I do this with a standard Fibre MODEM comes with the service?)
Line 123: Line 123:
  
 
The Optical Network Terminal (ONT) located within the property by default can have up to four Ethernet ports to use for connectivity. If you cannot connect all devices directly to the unit, you can connect a wireless/LAN router to the ONT to perform this task.
 
The Optical Network Terminal (ONT) located within the property by default can have up to four Ethernet ports to use for connectivity. If you cannot connect all devices directly to the unit, you can connect a wireless/LAN router to the ONT to perform this task.
 +
 +
 +
== Ports/ IP Addresses ==
 +
 +
 +
=== What ports have you blocked? ===
 +
 +
None.
 +
 +
 +
 +
=== What about Port 80 - is it blocked? ===
 +
 +
No, it is not blocked.
 +
 +
 +
 +
=== Can I get a static IP address? ===
 +
 +
Yes, you can.
 +
 +
 +
 +
=== How can I tell if my service can use DHCP instead of PPPoE? ===
 +
 +
The ONT at a customer location has nothing to do with DHCP. It is the gateway router on eXeTeL 's end that hands out Internet connections either DHCP or PPPoE.
 +
 +
You cannot make your connection work with DHCP just by changing your router's settings. Also, upgrading your router's firmware will not help. eXeTeL would need to update equipment on its end to allow DHCP.
 +
  
 
[[Category:Fibre Broadband]]
 
[[Category:Fibre Broadband]]

Revision as of 04:17, 9 September 2011

Fibre Broadband > Fibre - Support Information


Fibre Supplier and EU Responsibility

Accountability Type of fault Resolution
Supplier
  • Power Supply Unit (PSU)
  • Optical Network Terminal (ONT)
  • Drop cable down
  • Street network down
  • Backbone network
  • Switch components
Supplier will dispatch the required workforce to resolve these issues
End User
  • Battery backup failure
  • End user power outage
  • Street power outage
  • Internal wiring
  • Damage to NBN infrastructure (NTU, PSU, Drop cable...etc)
  • In premise gateway

Speed Test

How to run a speed test for Fibre?

Please visit Speed Tests page for specific instructions on Fibre Speed Tests.


Where can I test the speed of my Fibre Optic service?

Visit www.ozspeedtest.com or www.speedtest.net to test speed of your Fibre service.


MODEM and other Hardware for Fibre

Can I use my ADSL/Cable Router for Exetel's Fibre service?

You would be able to use these devices to the extent as an additional hub point to connect additional devices for the purpose of your own internal network. From the router, you can merely connect to the Ethernet.


What type of equipment (MODEM, Filters…etc) will I need to set up the Optic Fibre service?

As the ONT (Optical Network Terminal) provided by our supplier has an Ethernet Port to connect to the Internet, you do not require any equipment to be connected to the Internet directly. Use a Router that has both WAN and LAN ports if you are managing your own internal network, as the ADSL MODEM/ Router does not support this.

Optical Network Terminal (ONT)

An ONT is used to terminate the fibre optic cable to the End User’s (EU) premises. It serves two purposes; one is to terminate the Fibre signal and two is to give the EU a usable interface with the ONT in order to use the service. It works by taking the Fibre laser light signal and converting that back to Copper signals used inside the premises in case of the Internet, it will translate Fibre back to Ethernet.

Fibre faults follow the same process as our current ADSL faults. You must first validate the fault as being of the supplier network, you can do this depending on the type of fault, using the lights on the ONT or having the EU perform testing to demonstrate the fault.

The DATA light on the ONT should come on when a successful authentication attempt is done. Testing the other DATA ports will assist in verifying a faulty ONT port.


The ONT provided by NEC contains;

  • 4 10/100 Base –T Ethernet Ports
  • 2 POTS services for Voice
  • One Analog Video port for TV


Fibre9.gif


Fibre10.gif


  • Every ONT must have its own PSU
  • A BBU is a Battery Back Up that can optionally be installed during activation
  • The Customer will need to find their own Battery
  • Data port 1 is the general assumption for the service delivery point on the ONT


Power Supply Units (PSU)

The PSU provides a 240v to 12v regulated power supply and it comes with an empty battery backup compartment.


Fibre11.gif


Fibre12.gif


  • It is always recommended to have a router Gateway between the ONT and PC/Devices
  • It should only be directly connected during testing as per troubleshooting
  • While the ONT has inputs and readings for other services (Telephone/TV etc) at this time DATA is our only requirement


Fiber Distribution Terminal (FDT)

FDTs are the black objects where the drops that go to individual houses are connected. FDT can go on a pole or underground depending on how your utilities are delivered. Most are 4-port terminals but they do come in different sizes.


AerialFDT.gif


Optical Splitters

Optical networking system needs signals to be coupled, splitted, distributed, this requires optical splitter to achieve. Fiber optic splitter is used to split a fiber optic beam into several beams at a certain splitting ratio. It is widely used in Optical communication system. Currently this is not essential to use the fibre service.


OS.gif


Battery Backup Unit (BBU)

Purpose of this is to prepare a customer for a power outage as the Fibre will go off if power is out. The customer is responsible for buying the battery pack.


BBP.gif


I have more than two computers at home and need to share Internet simultaneously. Can I do this with a standard Fibre MODEM comes with the service?

The Optical Network Terminal (ONT) located within the property by default can have up to four Ethernet ports to use for connectivity. If you cannot connect all devices directly to the unit, you can connect a wireless/LAN router to the ONT to perform this task.


Ports/ IP Addresses

What ports have you blocked?

None.


What about Port 80 - is it blocked?

No, it is not blocked.


Can I get a static IP address?

Yes, you can.


How can I tell if my service can use DHCP instead of PPPoE?

The ONT at a customer location has nothing to do with DHCP. It is the gateway router on eXeTeL 's end that hands out Internet connections either DHCP or PPPoE.

You cannot make your connection work with DHCP just by changing your router's settings. Also, upgrading your router's firmware will not help. eXeTeL would need to update equipment on its end to allow DHCP.